HXE-28DWT Copper wire drawing machine with annealer
I. Quick details
HXE-28DWT is used to draw and annealing single bare copper wire
from 1.1-1.6mm to 0.1-0.32mm.
II. Components
| Name | Quantity |
| 1. Pay-off stands | 1 set |
| 2. HXE-28DWT main drawing machine | 1 set |
| 3. Electrical control system | 1 set |
| 4. Steam generator | 1 set |
| 5. Lubrication tank and Pump | Optional |
| 6. Spare parts |
III. Main Technical parameters
1. Usage: Copper wire drawing and annealing
2. Inlet diameter: 1.1-1.6mm
3. Outlet diameter: 0.1-0.32mm
4. Max. mechanical speed: 1500m/min.
5. Dies: 28 dies
6. Slip ratio: 13%, Finished capstan slip ratio: 8%
7. Main motor: AC 3 Phase 18.5KW, Inverter control
8. Take up motor: AC 3 Phase 3.7KW, Inverter control
9. Take up capacity: 50kg for diameter 300mm iron spool (Customize)
10. Spool size: Diameter 300mm/Max (Customize)
11. Capstans: Ceramic plasma, Drawing capstan 316mm, Final capstan
268mm
12. Capstan lubrication: Water pipe spray
13. Traversing: 110W synchronous motor,transmission by timing
belts.
14. Brake: 20KG-M Electromagnetic brake
15. Air pressure: 4-6kg/cm2
16. Annealing pulley: Diameter 120mm
17. Annealing volt: 50V
18. Annealing current: 300A
19. Annealing motor power: 15KVA
20. Power source: (customize)
21. Tension control: Annealer & Spooler Tension control by Swing
arms, Air pressure auto adjust.
22. Tension control: Weight balance
23. Machine dimension(L*W*H): 3500mm*1600mm*2500mm, Machine
weight:3200kg
IV. Shipping & Installation
Shipping
There are two lifting rings on the drawing machine, four on then
annealing machine.
Installation (See attached drawing)
According to the drawing, make the foundation.
When machine is in position, install bolts and adjust the center
line.
When concrete is drying, adjust center line again and fix the
bolts.
Adjust
Before adjusting, check and clean all parts.
V. Advantage and after-sale service
A: Advantage
(1). HENGXIE has some world famous parts suppliers, has special
lubrication system for the gears and bearing.
(2). Body and other key components and parts are produced by our
own factory , quality is reliable.
(3). DC. three-section annealing
(4). Our company’s developing process in more than 10 years.
B: After-sale service
Our company for all machine product, since the shipment date, our
company free after sale maintenance service guarantee period is:
(1) 1 year for mechanical part.
(2) 6 month for electrical part.
Under these situation mentioned, the Seller will not take
responsibility, but if the Buyer agree, will charge fees
accordingly to repair the machine.
A. Due to wrong operation while shipping.
B. Due to Buyer`s wrong preparation that may cause damage to the
machine.
C. Due to Buyer`s wrong operation that may cause damage to the
machine.
D. Not in the consuming part list.
E. After agreement are made for the shipping, for any damage, Buyer
should inform Seller in letter form to repair in seven days, If
beyond the dare, Seller shall take no responsibility.
F. For any other failures due to acts of God (such as lightning,
typhoon, earthquake, riots, war, fire or flood) and other factors
that will cause damage, Seller shall take no responsibility.
G. Seller guarantee provide long term support regarding the parts
and teach. After warranty, will charge accordingly.
